Langues

Laboratoire de recherche
UMR 6602 - UCA/CNRS/SIGMA

Annuaire

Gayton Nicolas


Photo
Fonction : Enseignant chercheur (Permanent Ip)
Axe : Mms
Thème : Mpms
Téléphone : +33 73 28 81
Fax : +33 4 7328 8027



Publications associées :
64 publication trouvées


2016
ACL
FAURIAT W., MATTRAND C., GAYTON N., BEAKOU A., CEMBRZYNSKI T.
Estimation of road profile variability from measured vehicle responses



LELI\`EVRE N., BEAUREPAIRE P., MATTRAND C., GAYTON N., OSTMANE A.
On the consideration of uncertainty in design: Optimization - Reliability - Robustness



2015
ACTI
FAURIAT W., MATTRAND C., GAYTON N., BEAKOU A.
An Application of Stochastic Simulation to the Study of the Variability of Road Induced Fatigue Loads



ACTN
FAURIAT W., MATTRAND C., GAYTON N., BEAKOU A.
Analyse de la variabilité des chargements de fatigue dans l'automobile et influence sur les prévisions de fiabilité.



2014
ACL
BUCAS S., RUMELHART P., GAYTON N., CHATEAUNEUF A.
A global procedure for reliability assessment of crane structural elements



DUMAS A., GAYTON N., YVESDANTAN J., SUDRET B.
A new system formulation for the tolerance analysis of overconstrained mechanisms



FAURIAT W., GAYTON N.
AK-SYS: an adaptation of the AK-MCS method for system reliability



DUMAS A., YVESDANTAN J., GAYTON N.
An iterative tolerance analysis procedure to deal with linearized behavior models.



DUMAS A., YVESDANTAN J., GAYTON N.
Impact of the behaviour model linearisation strategy on the tolerance analysis of hyperstatic mechanisms



ACTI
DUMAS A., YVESDANTAN J., GAYTON N.
Tolerance analysis procedure to minimise the approximation error due to the linearisation of the behaviour model



2013
ACL
ECHARD B., GAYTON N., LEMAIRE M., RELUN N.
A combined Importance sampling and kriging reliability method for small failure probabilities with time demanding numerical models



ECHARD B., GAYTON N., BIGNONNET A.
A reliability analysis method for fatigue design



BEAUCAIRE P., GAYTON N., YVESDANTAN J., DUC E.
Statistical tolerance analysis of a mechanism with gaps based on system reliability methods



BEAUCAIRE P., GAYTON N., YVESDANTAN J., DUC E.
Statistical tolerance analysis of over-constrained mechanism using system reliability methods



BUCAS S., RUMELHART P., GAYTON N., CHATEAUNEUF A.
Stress-Strength Interference Method Applied for the Fatigue Design of Tower Cranes.



YVESDANTAN J., GAYTON N., QURESHI J., LEMAIRE M., ETIENNE A.
Tolerance Analysis Approach based on the Classification of Uncertainty (Aleatory/Epistemic)



ACTI
BUCAS S., RUMELHART P., GAYTON N., CHATEAUNEUF A.
Probabilistic approach for the fatigue design of tower cranes



BUCAS S., RUMELHART P., GAYTON N., CHATEAUNEUF A.
Probabilistic approach for the fatigue design of tower cranes



DUMAS A., GAYTON N., YVESDANTAN J.
The use of kriging for the tolerance analysis of complex system



2012
ACL
QURESHI J., YVESDANTAN J., BEAUCAIRE P., GAYTON N.
A statistical tolerance analysis approach for over-constrained mechanism based on optimization and Monte Carlo simulation



DUMAS A., ECHARD B., GAYTON N., ROCHAT O., YVESDANTAN J.
AK-ILS : an active Learning method based on kriging for the inspection of large surfaces



BEAUCAIRE P., GAYTON N., DUC E., LEMAIRE M., YVESDANTAN J.
Statistical tolerance analysis of an hyperstatic lechanism with gaps using system reliability methods



ACTI
DUMAS A., ECHARD B., GAYTON N., ROCHAT O.
AK-ILS : A new Active learning method based on Kriging for the Inspection of Large Surface.



NOTIN A., LUCDULONG J., VILLON P., GAYTON N., GOUALI A.
SLDLT : a modification of the Cholesky decomposition to speed up Monte Carlo simulations



BEAUCAIRE P., GAYTON N., YVESDANTAN J., DUC E., LEMAIRE M.
Statistical tolerance analysis of a mechanism with gaps based on system reliability methods.



YVESDANTAN J., GAYTON N., QURESHI J., LEMAIRE M., ETIENNE A.
Tolerance analysis approach based on the classification of uncertainties (aleatory / epistemic)



HDR
GAYTON N.
Méthodes probabilistes pour la conception mécanique Application à la fatigue des structures et à l’analyse des tolérances



2011
ACL
ECHARD B., GAYTON N., LEMAIRE M.
AK-MCS: an Active learning reliability method combining Kriging and Monte Carlo Simulation



GAYTON N., BEAUCAIRE P., BOURINET J., DUC E., LEMAIRE M., GAUVRIT L.
APTA: Advanced Probability - based Tolerance Analysis of products



QURESHI A., SABRI V., DANTAN J., BEAUCAIRE P., GAYTON N.
Statistical Tolerance Analysis � Formalization by quantifiers \& Implementation by Opimization and Monte Carlo Simulation



ACLN
GAYTON N., BEAUCAIRE P., DUC E., LEMAIRE M.
The APTA method for the tolerance analysis of products - comparison of capability-based tolerance and inertial tolerance



ACTI
ECHARD B., GAYTON N., LEMAIRE M.
A Kriging improvement of the Monte Carlo Simulation : AK-MCS method



GAYTON N.
Approfi project – A new approach of reliability Assessment of structures subjected to fatigue



NOTIN A., DULONG J., GAYTON N., VILLON P., LEMAIRE M., JAFFAL H.
RPCM: A strategy to perform reliability analysis using polynomial chaos and resampling - Application to fatigue design



ECHARD B., GAYTON N., LEMAIRE M., AFZALI M., BIGNONNET A., BOUCARD P., DEFAUX G., DULONG J., GHOUALI A., LEFEBVRE F., PYRE A.
Reliability assessment of an aerospace component subjected to fatigue loadings: APPRoFi project



ECHARD B., GAYTON N., LEMAIRE M., BIGNONNETA A.
Reliability assessment of an aerospace component subjected to fatigue loadings: APPRoFi project.



BOUCARD P., NERON D., RELUN N., ECHARD B., GAYTON N., LEMAIRE M., AFZALI M., LEFEBVRE F., BIGNONNET A., DEFAUX G., DULONG J., OTSMANE A., CHEROUALI H.
Reliability assessment of an aircraft engine assembly: APPRoFi project



ALAINBOUCARD P., NERON D., RELUN N., ECHARD B., GAYTON N.
Reliability assessment of an aircraft engine assembly: APPRoFi project



INV
GAYTON N., ECHARD B., AFZALI M., BIGNONNET A., BOUCARD P., DEFAUX G., DULONG J., GHOUALI A., LEFEBVRE F., MASMOUDI M., NOTIN A., NERON D., OSTMANE A., PYRE A., RELUN N.
Approfi project - A new approach of reliability Assessment of structures subjected to fatigue



2010
ACLN
NOTIN A., GAYTON N., DULONG J., LEMAIRE M., VILLON P.
RPCM: A strategy to perform reliability analysis using polynomial chaos and resampling - application to fatigue design



ACTI
ECHARD B., GAYTON N., LEMAIRE M.
AK-MCS: an Active learning reliability method combining Kriging and Monte Carlo Simulation to compute the probability of failure efficiently



GAYTON N., BEAUCAIRE P., DUC E., LEMAIRE M.
Application des méthodes fiabilistes au tolérancement statistique des systèmes mécaniques



NOTIN A., DULONG J., GAYTON N., VILLON P.
SLD: a stochastic approach of the LDL decomposition to speed up Monte Carlo simulations



NOTIN A., LUCDULONG J., GAYTON N., VILLON P.
SLDL: a stochastic approach of the LDL decomposition to speed up Monte Carlo simulations



NOTIN A., LUCDULONG J., VILLON P., GAYTON N., LEMAIRE M.
SLDLT : A new approach to speed up Monte Carlo simulations



ECHARD B., GAYTON N., LEMAIRE M.
Structural Reliability Assessment using Kriging metamodel and Monte Carlo simulation: AK-MCS method



ECHARD B., GAYTON N., LEMAIRE M.
Structural Reliability Assessment using a Kriging Metamodel and a Sequential Design of Experiments



2009
ACL
GAYTON N., LEMAIRE M.
Reliability assessment of structures subjected to fatigue failure



ACTI
NOTIN A., LUCDULONG J., GAYTON N., VILLON P.
A strategy based on LDLT decomposition to speed up Monte Carlo simulations : application to fatigue



NOTIN A., GAYTON N., LUCDULONG J., LEMAIRE M., VILLON P.
A strategy to perform reliability analysis using polynomial chaos and resampling: application to fatigue design



NOTIN A., GAYTON N., DULONG J., LEMAIRE M., VILLON P.
A strategy to perform reliability analysis using polynomial chaos and resampling: application to fatigue design



NOTIN A., LUCDULONG J., VILLON P., GAYTON N.
Crout decomposition for stochastic simulation



NOTIN A., DULONG J., VILLON P., GAYTON N.
Crout decomposition for stochastic simulation



ECHARD B., GAYTON N., LEMAIRE M.
Reliability assessment of structures subjected to fatigue failure using kriging methods



ECHARD B., GAYTON N., LEMAIRE M.
Reliability assessment of structures subjected to fatigue failure using kriging methods



NOTIN A., GAYTON N., LEMAIRE M., DULONG J.
Stochastic fatigue lifetime computation : evaluation by polynomial chaos and resampling



NOTIN A., GAYTON N., LEMAIRE M., LUCDULONG J.
Stochastic fatigue lifetime computation: evaluation by polynomial chaos and resampling



GAYTON N., DUC E., LEMAIRE M.
The use of probabilistic approach for the tolerancing management in design process



GAYTON N., DUC E., LEMAIRE M.
The use of probabilistic approach for the tolerancing management in design process



NOTIN A., DULONG J., GAYTON N., VILLON P.
Utilisation de la décomposition LDLt en simulation stochastique



2008
GAYTON N., GAUVRIT L., DUC E., LEMAIRE M.
A Methodology to assess the out tolerance probability with linear or non linear functional requirements



GAYTON N., LEMAIRE M.
Reliability Assessment of Structures Subjected to Fatigue Fracture



2007
GAYTON N., LEMAIRE M.
Calibration des coefficients partiels pour le dimensionnement des structures en fatigue



GAYTON N., LEMAIRE M.
Partial safety factor methodology applied to structural fatigue design





<-- retour à l'annuaire